Shenzhen ECON Technology Co.,Ltd
call us on: +8613620961024

Stepping motor Drive three phase use for laser cutting machine,dispenser

3 phase stepping motor driver,DC power supply,20~50V,peak current under 8.3A,pure sine current vector control technology,good application on dispenser,laser cutting and labeling machine

Product Details:

Product Introduction: stepping motor driver three phase for laser cutting machine,dispenser

3DH583.jpg

3DH583 is the new generation high performance fully digital stepper drive which base on 32bit DSP with a advanced algorithm .the power supply range is DC20~50V. it can drive frame 42--86mm 3 phase stepper motor .Ultra low noise and high smoothness at middle/low speed ,and high torque at high speed, which can be applied to different speed control applications. adopt smooth and accurate sinusoidal current vector control technology ,which make motor low heat .

Product Features: stepping motor driver three phase for laser cutting machine,dispenser

●new generation 32bit DSP 

●good smoothness ,low noise ,low heat 

●build-in micro step setting 

●build-in current setting 

●the standstill current can be set to 50%

●opto-isolated differential pulse input 

●the response frequency is up to 300KHz

●over voltage , under voltage, over current protection

Applications 

It can be used in various kinds of machines ,such as dispenser machine. floating machine, labelling machine, medical machine, laser cut machine,robot,soldering machine and so on ,its unique features make it an ideal solution for the applications which require low noise ,low vibration, low heat and high precision  

Mounting Dimension(unit:mm)

Product Function: stepping motor driver three phase for laser cutting machine,dispenser

Current Setting 

Peak current A)

RMS current (A)

SW1

SW2

SW3

SW4

2.1

1.5

Off

Off

Off

Off

2.5

1.8

On

Off

Off

Off

2.9

2.1

Off

On

Off

Off

3.2

2.3

On

On

Off

Off

3.6

2.6

Off

Off

On

Off

4.0

2.9

On

Off

On

Off

4.5

3.2

Off

On

On

Off

4.9

3.5

On

On

On

Off

5.3

3.8

Off

Off

Off

On

5.7

4.1

On

Off

Off

On

6.2

4.4

Off

On

Off

On

6.4

4.6

On

On

Off

On

6.9

4.9

Off

Off

On

On

7.3

5.2

On

Off

On

On

7.7

5.5

Off

On

On

On

8.3

5.9

On

On

On

On

SW5:OFF=Half Current

ON=Full Current

Microstep Setting 

Pul/rev

SW6

SW7

SW8

200

ON

ON

ON

400

OFF

ON

ON

500

ON

OFF

ON

1000

OFF

OFF

ON

2000

ON

ON

OFF

4000

OFF

ON

OFF

5000

ON

OFF

OFF

10000

OFF

OFF

OFF

Interface Description 

Name

Function

Description

PWR

Power light

When power on ,the green light is on

ALARM

Over current/under voltage/over voltage 

displaying light

If the drive Over current/under voltage/over voltage, 

the red light is on

PU+

Pulse input positive

Pulse signal: In single pulse (pulse/direction) mode,this input represents pulse signal, 

each falling edge active; 4-5V for High -level, 0.5V for low-level

Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V)

PU-

Pulse input negative

Pulse signal: In single pulse (pulse/direction) mode,this input represents pulse signal,

each falling edge active;4-5V for High -level, 0-0.5V for low-level

DR+

Direction  input positive

DIR signal: In single-pulse mode, this signal has low/high voltage levels, 

representing two directions of motor rotation;

Series connect resistors for current-limiting when +12V or +24V used.

(should connect 1k resistor for +12V,2k for +24V)

DR-

Direction input negative

DIR signal: In single-pulse mode, this signal has low/high voltage levels, 

representing two directions of motor rotation;

MF+

Enable input positive

Enable signal: This signal is used for enabling/disabling driver. 

High level for enabling the driver and low level for disabling the driver. 

Usually left UNCONNECTED (ENABLED).

Series connect resistors for current-limiting when +12V or +24V used.

(should connect 1k resistor for +12V,2k for +24V)

MF-

Enable input negative

Enable signal: This signal is used for enabling/disabling driver. 

High level for enabling the driver and low level for disabling the driver. 

Usually left UNCONNECTED (ENABLED).

V-

Power input COM

DC20-50V

V+

Power input VCC

U

Motor  U

Motor  U

V

Motor  V

Motor  V

W

Motor  W

Motor  W

!Note

A: Connect power supply rightly ,can’t exceed 50VDC 

B: If the control signal (PU, DR,MF ) is over 5V ,please connect resistors (at the PU+, DR+, MF+ terminals) for current-limiting.

C: If the alarm light is on ,please check it after power off

     a :the power supply range is 20V—50VDC or not ? b:is there any short on motor wire or others ?


Product Service: stepping motor driver three phase for laser cutting machine,dispenser

ECON provide technical service from start to end,and will offer one year warranty. Any problem,can send e-mail to our technical engineer and sales,or directly chat on our website.


Payment and Delivery: stepping motor driver three phase for laser cutting machine,dispenser

ECON supports T/T,Paypal,Western Union to make payment. We can arrange express,air and sea shipment,we have professional team to deal with logistic.


Recommendations: stepping motor driver three phase for laser cutting machine,dispenser

3 Phase Stepper Motor Nema 23 Series

3 Phase Stepper Motor Nema 34 Series

Power Supply




Equipped with professional 3 Phase Stepper Drive factory, It is a leading Stepping motor Drive three phase use for laser cutting machine,dispenser manufacturer and supplier.

Hot Tags: Stepping motor Drive three phase use for laser cutting machine,dispenser, manufacturer, supplier, factory
Feedback
Contact Us

Shenzhen ECON Technology Co.,Ltd

Add: 2F, Building B, Jintai Industrial Park, Hangcheng Avenue, Gushu Village, Xixiang Street, Bao'an Area, Shenzhen, Guangdong, China

Tel: 0755-2331 9542

Fax: 0755-2331 9542

Tel: +86 136 2096 1024

Email: enquiry@hybridservo.com

       technical01@hybridservo.com

Copyright © Shenzhen ECON Technology Co.,Ltd